|
Gland Dimensions Per Mil-G-5514 Standard for the following families of Piston, Shaft,
and Other Cylindrical Application Duraseal Seals
|
|
FM
|
FMH
|
FMI
|
FMIH
|
FME
|
FMEH
|
FMD
|
FMDH
|
|
CM
|
CMH
|
|
|
|
|
|
|
|
HM
|
HMH
|
HMI
|
HMIH
|
HME
|
HMEH
|
HMD
|
HMDH
|
|
RM
|
RMH
|
|
|
|
|
|
|
|
Note: The standard gland lengths ('G' dimensions) are insufficient for the
heavy heel seals (suffix H). See table below.
|
Size Dash Number
|
Nominal
Cross Section
|
G*
Gland Length
|
G**
Gland Length
|
R
Radius
|
E
Diametric Clearance Max
|
|
-006 thru -028
|
1/16†
|
.094/.104
|
.149/.159
|
..005/.015
|
.004
|
|
-110 thru -149
|
3/32
|
.141/.151
|
.183/.193
|
.005/.015
|
.004
|
|
-210 thru -247
|
1/8
|
.188/.198
|
.235/.245
|
.005/.025
|
.006
|
|
-325 thru -349
|
3/16
|
.281/.291
|
.334/.344
|
.005/.030
|
.006
|
|
-425 thru -460
|
1/4
|
.375/.385
|
.475/.485
|
.005/.030
|
.006
|
* All seals referenced above without
suffix H
** All seals referenced above with suffix H
† 1/16 CROSS SECTION SEALS ARE
RECOMMENDED FOR LIMITED SPACE APPLICATIONS ONLY. IF SPACE PERMITS,
USE 3/32" CROSS SECTION OR LARGER.
SEPARABLE GLAND DESIGN OR REDUCED
GLAND-WALL DESIGN SHOULD BE USED WHENEVER POSSIBLE.
|
3/32"
NOMINAL
CROSS SECTION
|
|
Size
Dash
Number
|
Piston
|
|
A
+.000
-.001
|
B
+.001
-.000
|
|
-110
|
.372
|
.550
|
|
-111
|
.435
|
.613
|
|
-112
|
.497
|
.675
|
|
-113
|
.560
|
.738
|
|
-114
|
.622
|
.800
|
|
-115
|
.685
|
.863
|
|
-116
|
.747
|
.925
|
|
-117
|
.813
|
.991
|
|
-118
|
.875
|
1.053
|
|
-119
|
.938
|
1.116
|
|
-120
|
1.000
|
1.178
|
|
-121
|
1.063
|
1.241
|
|
-122
|
1.125
|
1.303
|
|
-123
|
1.188
|
1.366
|
|
-124
|
1.250
|
1.428
|
|
-125
|
1.313
|
1.491
|
|
-126
|
1.375
|
1.553
|
|
-127
|
1.438
|
1.616
|
|
-128
|
1.500
|
1.678
|
|
-129
|
1.563
|
1.741
|
|
-130
|
1.627
|
1.805
|
|
-131
|
1.689
|
1.867
|
|
-132
|
1.752
|
1.930
|
|
-133
|
1.814
|
1.992
|
|
-134
|
1.877
|
2.055
|
|
|
+.000
|
+.002
|
|
|
-.002
|
-.000
|
|
-135
|
1.940
|
2.118
|
|
-136
|
2.002
|
2.180
|
|
-137
|
2.065
|
2.243
|
|
-138
|
2.127
|
2.305
|
|
-139
|
2.190
|
2.368
|
|
-140
|
2.252
|
2.430
|
|
-141
|
2.315
|
2.493
|
|
-142
|
2.377
|
2.555
|
|
-143
|
2.440
|
2.618
|
|
-144
|
2.502
|
2.680
|
|
-145
|
2.565
|
2.743
|
|
-146
|
2.627
|
2.805
|
|
-147
|
2.690
|
2.868
|
|
-148
|
2.752
|
2.930
|
|
-149
|
2.815
|
2.993
|
|
|
Size
Dash
Number
|
Shaft
|
|
A
+.000
-.001
|
B
+.001
-.000
|
|
-110
|
.373
|
.551
|
|
-111
|
.435
|
.613
|
|
-112
|
.498
|
.676
|
|
-113
|
.560
|
.738
|
|
-114
|
.623
|
.801
|
|
-115
|
.685
|
.863
|
|
-116
|
.748
|
.926
|
|
-117
|
.810
|
.988
|
|
-118
|
.873
|
1.051
|
|
-119
|
.935
|
1.113
|
|
-120
|
.998
|
1.176
|
|
-121
|
1.060
|
1.238
|
|
-122
|
1.123
|
1.301
|
|
-123
|
1.185
|
1.363
|
|
-124
|
1.248
|
1.426
|
|
-125
|
1.310
|
1.488
|
|
-126
|
1.373
|
1.551
|
|
-127
|
1.435
|
1.613
|
|
-128
|
1.498
|
1.676
|
|
-129
|
1.560
|
1.738
|
|
-130
|
1.623
|
1.801
|
|
-131
|
1.685
|
1.863
|
|
-132
|
1.748
|
1.926
|
|
-133
|
1.810
|
1.988
|
|
-134
|
1.873
|
2.015
|
|
|
+.000
|
+.002
|
|
|
-.002
|
-.000
|
|
-135
|
1.936
|
2.114
|
|
-136
|
1.998
|
2.176
|
|
-137
|
2.061
|
2.239
|
|
-138
|
2.123
|
2.301
|
|
-139
|
2.186
|
2.364
|
|
-140
|
2.248
|
2.426
|
|
-141
|
2.311
|
2.489
|
|
-142
|
2.373
|
2.551
|
|
-143
|
2.436
|
2.614
|
|
-144
|
2.498
|
2.676
|
|
-145
|
2.561
|
2.739
|
|
-146
|
2.623
|
2.801
|
|
-147
|
2.686
|
2.864
|
|
-148
|
2.748
|
2.926
|
|
-149
|
2.811
|
2.989
|
|
|
3/16"
NOMINAL
CROSS SECTION
|
|
Size
Dash
Number
|
Piston
|
|
A
+.000
-.002
|
B
+.002
-.000
|
|
-325
|
1.495
|
1.867
|
|
-326
|
1.620
|
1.991
|
|
-327
|
1.746
|
2.118
|
|
-328
|
1.871
|
2.243
|
|
-329
|
1.996
|
2.368
|
|
-330
|
2.121
|
2.493
|
|
-331
|
2.246
|
2.618
|
|
-332
|
2.371
|
2.743
|
|
-333
|
2.496
|
2.868
|
|
-334
|
2.621
|
2.993
|
|
-335
|
2.746
|
3.118
|
|
-336
|
2.871
|
3.243
|
|
-337
|
2.996
|
3.368
|
|
-338
|
3.121
|
3.493
|
|
-339
|
3.246
|
3.618
|
|
-340
|
3.371
|
3.743
|
|
-341
|
3.496
|
3.868
|
|
-342
|
3.621
|
3.993
|
|
-343
|
3.746
|
4.118
|
|
-344
|
3.871
|
4.243
|
|
-345
|
3.996
|
| | | 
